Deliver to
United Kingdom
Media preparators designed for preparation and sterilisation of agar-containing nutrient media and other sterile liquids (10 to 120 l nominal volume), with microprocessor-controlled fully automatic programme sequence. The Systec Mediaprep series includes stronger heating elements, rapid cooling, magnetic stirring, inner vessel, temperature controlled door lock, dispensing outlet and inlet port for adding additives. - Fully automatic microprocessor control incorporating 100 programmes. - Sterilisation temperature pre-selectable up to 138 °C / 3.8 bar. - Novel automatic door closure with safety-lock system, lip-gasket out of silicone and opening at the push of a button. - Thermal door lock, controlled by pressure and medium temperature acc. to Pressure Vessel Regulations. - Pressure vessel made out of high quality pharmaceutical grade titanium-stabilised st. steel 1.4571 (V4A, AISI 316 Ti), electro polished, resistant against chemicals, easy to clean. - All sterilisation programmes with pre-selectable sterilisation parameters and automatic programme sequence. - Rapid cooling with recirculating sterile water, heat exchanger and recirculation pump. - Electronic pressure transducer for pressure and temperature regulation. - Autofill: automatic demineralised water feed for steam generation. - Steam exhaust condensation: water-cooled with thermostatic control. - Start by clock / timer for programmable start-time. - Prepared for subsequent printer connection. - RS232 interface for data transfer. - Temperature holding programme for keeping agar solutions warm. - Base plate for vessels, baskets etc. when used as autoclave. - Thermal insulation out of Hanno-Tect, no risk of particle dissociation. - Safety pressure release valve. - Safety cut off at low water level. - Safety cut off at excess temperature. - Direct electrical heated through strong heating elements for fast heat-up. - Fast cooling through recirculation of in-line sterilised demineralised water, cooled by a plate heat exchanger with cooling water connection. - Continuous mixing through a stirrer on the bottom of the media-vessel, contact free driven by a strong magnetic motor. - Permanent temperature control with a PT 100 temperature load sensor, directly inside the media. - Inlet-nozzle with safety screw-closure for filling of additives after sterilisation. - Media removal through a flexible silicone tubing (either by selectable internal pressure inside the chamber and an electronically controlled pinch valve or with an optional peristaltic pump). Furthermore all filling lines for petri-dishes available on the market or other dispensing devices can be connected, without any exception. The inner filling tube and the dispensing nozzle are sterilised in-line, during the sterilisation cycle. - Easy cleaning and operational readiness through exchangeable, removable inner vessel. Thereby no risk of cross-contamination between the different batches. Media preparators designed for preparation and sterilisation of agar-containing nutrient media and other sterile liquids (10 to 120 l nominal volume), with microprocessor-controlled fully automatic programme sequence. The Systec Mediaprep series includes stronger heating elements, rapid cooling, magnetic stirring, inner vessel, temperature controlled door lock, dispensing outlet and inlet port for adding additives. - Fully automatic microprocessor control incorporating 100 programmes. - Sterilisation temperature pre-selectable up to 138 °C / 3.8 bar. - Novel automatic door closure with safety-lock system, lip-gasket out of silicone and opening at the push of a button. - Thermal door lock, controlled by pressure and medium temperature acc. to Pressure Vessel Regulations. - Pressure vessel made out of high quality pharmaceutical grade titanium-stabilised st. steel 1.4571 (V4A, AISI 316 Ti), electro polished, resistant against chemicals, easy to clean. - All sterilisation programmes with pre-selectable sterilisation parameters and automatic programme sequence. - Rapid cooling with recirculating sterile water, heat exchanger and recirculation pump. - Electronic pressure transducer for pressure and temperature regulation. - Autofill: automatic demineralised water feed for steam generation. - Steam exhaust condensation: water-cooled with thermostatic control. - Start by clock / timer for programmable start-time. - Prepared for subsequent printer connection. - RS232 interface for data transfer. - Temperature holding programme for keeping agar solutions warm. - Base plate for vessels, baskets etc. when used as autoclave. - Thermal insulation out of Hanno-Tect, no risk of particle dissociation. - Safety pressure release valve. - Safety cut off at low water level. - Safety cut off at excess temperature. - Direct electrical heated through strong heating elements for fast heat-up. - Fast cooling through recirculation of in-line sterilised demineralised water, cooled by a plate heat exchanger with cooling water connection. - Continuous mixing through a stirrer on the bottom of the media-vessel, contact free driven by a strong magnetic motor. - Permanent temperature control with a PT 100 temperature load sensor, directly inside the media. - Inlet-nozzle with safety screw-closure for filling of additives after sterilisation. - Media removal through a flexible silicone tubing (either by selectable internal pressure inside the chamber and an electronically controlled pinch valve or with an optional peristaltic pump). Furthermore all filling lines for petri-dishes available on the market or other dispensing devices can be connected, without any exception. The inner filling tube and the dispensing nozzle are sterilised in-line, during the sterilisation cycle. - Easy cleaning and operational readiness through exchangeable, removable inner vessel. Thereby no risk of cross-contamination between the different batches.
Product Detail
Specially designed for the requirements in laboratories, these autoclaves make sterilisation processes safe, accurate, reproducible and validatable. 3 model ranges with different performance. Systec DX: For all laboratory applications, incl. sophisticated state-of-the-art sterilisation processes. With numerous options for validatable sterilisation. Systec DE: For basic laboratory applications. With limited options for process optimisation. Systec DB: For simple process applications. No options available for process optimisation. Standard features: - Housing, support frame and pressure vessel made of corrosion-resistant st. steel. - Temperature and pressure range 140 °C, 4 bar. - LCD display and fully automatic microprocessor control. - Code-secured access rights for changing parameters and further safety-relevant intervention. - Flexible PT-100 temperature sensor. - Internal heating elements within the autoclave chamber. - Number of sterilisation programmes: 12. - Internal memory for storing up to 500 sterilisation cycles. - Timer for starting programmes. - Autofill: automatic demineralised water feed for steam generation. - Flexible PT-100 temperature sensor. - Temperature holding function for liquids after programme finish. - Special programme for Durham tubes. - Calculation of F0 value. - Special programme for waste sterilisation with pulsed heat-up for more efficient air exhaust. - Water-cooled steam exhaust, thermostatically controlled. - Programmable automatic door-opening on completion of programme. - RS-232 and RS-485 interfaces for external data transmission (network-compatible). Specially designed for the requirements in laboratories, these autoclaves make sterilisation processes safe, accurate, reproducible and validatable. 3 model ranges with different performance. Systec DX: For all laboratory applications, incl. sophisticated state-of-the-art sterilisation processes. With numerous options for validatable sterilisation. Systec DE: For basic laboratory applications. With limited options for process optimisation. Systec DB: For simple process applications. No options available for process optimisation. Standard features: - Housing, support frame and pressure vessel made of corrosion-resistant st. steel. - Temperature and pressure range 140 °C, 4 bar. - LCD display and fully automatic microprocessor control. - Code-secured access rights for changing parameters and further safety-relevant intervention. - Flexible PT-100 temperature sensor. - Internal heating elements within the autoclave chamber. - Number of sterilisation programmes: 12. - Internal memory for storing up to 500 sterilisation cycles. - Timer for starting programmes. - Autofill: automatic demineralised water feed for steam generation. - Flexible PT-100 temperature sensor. - Temperature holding function for liquids after programme finish. - Special programme for Durham tubes. - Calculation of F0 value. - Special programme for waste sterilisation with pulsed heat-up for more efficient air exhaust. - Water-cooled steam exhaust, thermostatically controlled. - Programmable automatic door-opening on completion of programme. - RS-232 and RS-485 interfaces for external data transmission (network-compatible).
Product Detail
Specially designed for the requirements in laboratories, these autoclaves make sterilisation processes safe, accurate, reproducible and validatable. 3 model ranges with different performance. Systec VX: For all laboratory applications, incl. sophisticated state-of-the-art sterilisation processes. With numerous options for validatable sterilisation. Systec VE: For basic laboratory applications. With limited options for process optimisation. Systec VB: For simple process applications. No options available for process optimisation. Standard Features: - Housing, support frame and pressure vessel made of corrosion-resistant st. steel. - Temperature and pressure range 140 °C, 4 bar. - LCD display and fully automatic microprocessor control. - Code-secured access rights for changing parameters and further safety-relevant intervention. - Flexible PT-100 temperature sensor. - Internal heating elements within the autoclave chamber. - Number of sterilisation programmes: 12. - Internal memory for storing up to 500 sterilisation cycles. - Timer for starting programmes. - Autofill: automatic demineralised water feed for steam generation. - Flexible PT-100 temperature sensor. - Temperature holding function for liquids after programme finish. - Special programme for Durham tubes. - Calculation of F0 value. - Special programme for waste sterilisation with pulsed heat-up for more efficient air exhaust. - Water-cooled steam exhaust, thermostatically controlled. - Programmable automatic door-opening on completion of programme. - RS-232 and RS-485 interfaces for external data transmission (network-compatible). Specially designed for the requirements in laboratories, these autoclaves make sterilisation processes safe, accurate, reproducible and validatable. 3 model ranges with different performance. Systec VX: For all laboratory applications, incl. sophisticated state-of-the-art sterilisation processes. With numerous options for validatable sterilisation. Systec VE: For basic laboratory applications. With limited options for process optimisation. Systec VB: For simple process applications. No options available for process optimisation. Standard Features: - Housing, support frame and pressure vessel made of corrosion-resistant st. steel. - Temperature and pressure range 140 °C, 4 bar. - LCD display and fully automatic microprocessor control. - Code-secured access rights for changing parameters and further safety-relevant intervention. - Flexible PT-100 temperature sensor. - Internal heating elements within the autoclave chamber. - Number of sterilisation programmes: 12. - Internal memory for storing up to 500 sterilisation cycles. - Timer for starting programmes. - Autofill: automatic demineralised water feed for steam generation. - Flexible PT-100 temperature sensor. - Temperature holding function for liquids after programme finish. - Special programme for Durham tubes. - Calculation of F0 value. - Special programme for waste sterilisation with pulsed heat-up for more efficient air exhaust. - Water-cooled steam exhaust, thermostatically controlled. - Programmable automatic door-opening on completion of programme. - RS-232 and RS-485 interfaces for external data transmission (network-compatible).
Product Detail
Specially designed for the requirements in laboratories, these autoclaves make sterilisation processes safe, accurate, reproducible and validatable. 3 model ranges with different performance. Systec VX: For all laboratory applications, incl. sophisticated state-of-the-art sterilisation processes. With numerous options for validatable sterilisation. Systec VE: For basic laboratory applications. With limited options for process optimisation. Systec VB: For simple process applications. No options available for process optimisation. Standard Features: - Housing, support frame and pressure vessel made of corrosion-resistant st. steel. - Temperature and pressure range 140 °C, 4 bar. - LCD display and fully automatic microprocessor control. - Code-secured access rights for changing parameters and further safety-relevant intervention. - Flexible PT-100 temperature sensor. - Integrated, separate steam generator. - Number of sterilisation programmes: up to 25 (on request). - Internal memory for storing up to 500 sterilisation cycles. - Timer for starting programmes. - Autofill: automatic demineralised water feed for steam generation. - Flexible PT-100 temperature sensor. - Additional temperature sensor in condense exhaust. - Temperature holding function for liquids after programme finish. - Special programme for Durham tubes. - Calculation of F0 value. - Special programme for waste sterilisation with pulsed heat-up for more efficient air exhaust. - Water-cooled steam exhaust, thermostatically controlled. - Programmable automatic door-opening on completion of programme. - RS-232 and RS-485 interfaces for external data transmission (network-compatible). Specially designed for the requirements in laboratories, these autoclaves make sterilisation processes safe, accurate, reproducible and validatable. 3 model ranges with different performance. Systec VX: For all laboratory applications, incl. sophisticated state-of-the-art sterilisation processes. With numerous options for validatable sterilisation. Systec VE: For basic laboratory applications. With limited options for process optimisation. Systec VB: For simple process applications. No options available for process optimisation. Standard Features: - Housing, support frame and pressure vessel made of corrosion-resistant st. steel. - Temperature and pressure range 140 °C, 4 bar. - LCD display and fully automatic microprocessor control. - Code-secured access rights for changing parameters and further safety-relevant intervention. - Flexible PT-100 temperature sensor. - Integrated, separate steam generator. - Number of sterilisation programmes: up to 25 (on request). - Internal memory for storing up to 500 sterilisation cycles. - Timer for starting programmes. - Autofill: automatic demineralised water feed for steam generation. - Flexible PT-100 temperature sensor. - Additional temperature sensor in condense exhaust. - Temperature holding function for liquids after programme finish. - Special programme for Durham tubes. - Calculation of F0 value. - Special programme for waste sterilisation with pulsed heat-up for more efficient air exhaust. - Water-cooled steam exhaust, thermostatically controlled. - Programmable automatic door-opening on completion of programme. - RS-232 and RS-485 interfaces for external data transmission (network-compatible).
Product Detail
Specially designed for the requirements in laboratories, these autoclaves make sterilisation processes safe, accurate, reproducible and validatable. 3 model ranges with different performance. Systec VX: For all laboratory applications, incl. sophisticated state-of-the-art sterilisation processes. With numerous options for validatable sterilisation. Systec VE: For basic laboratory applications. With limited options for process optimisation. Systec VB: For simple process applications. No options available for process optimisation. Standard Features: - Housing, support frame and pressure vessel made of corrosion-resistant st. steel. - Temperature and pressure range 140 °C, 4 bar. - LCD display and fully automatic microprocessor control. - Code-secured access rights for changing parameters and further safety-relevant intervention. - Flexible PT-100 temperature sensor. - Internal heating elements within the autoclave chamber. - Number of sterilisation programmes: 12. - Internal memory for storing up to 500 sterilisation cycles. - Timer for starting programmes. - Autofill: automatic demineralised water feed for steam generation. - Flexible PT-100 temperature sensor. - Temperature holding function for liquids after programme finish. - Special programme for Durham tubes. - Calculation of F0 value. - Special programme for waste sterilisation with pulsed heat-up for more efficient air exhaust. - Water-cooled steam exhaust, thermostatically controlled. - Programmable automatic door-opening on completion of programme. - RS-232 and RS-485 interfaces for external data transmission (network-compatible). Specially designed for the requirements in laboratories, these autoclaves make sterilisation processes safe, accurate, reproducible and validatable. 3 model ranges with different performance. Systec VX: For all laboratory applications, incl. sophisticated state-of-the-art sterilisation processes. With numerous options for validatable sterilisation. Systec VE: For basic laboratory applications. With limited options for process optimisation. Systec VB: For simple process applications. No options available for process optimisation. Standard Features: - Housing, support frame and pressure vessel made of corrosion-resistant st. steel. - Temperature and pressure range 140 °C, 4 bar. - LCD display and fully automatic microprocessor control. - Code-secured access rights for changing parameters and further safety-relevant intervention. - Flexible PT-100 temperature sensor. - Internal heating elements within the autoclave chamber. - Number of sterilisation programmes: 12. - Internal memory for storing up to 500 sterilisation cycles. - Timer for starting programmes. - Autofill: automatic demineralised water feed for steam generation. - Flexible PT-100 temperature sensor. - Temperature holding function for liquids after programme finish. - Special programme for Durham tubes. - Calculation of F0 value. - Special programme for waste sterilisation with pulsed heat-up for more efficient air exhaust. - Water-cooled steam exhaust, thermostatically controlled. - Programmable automatic door-opening on completion of programme. - RS-232 and RS-485 interfaces for external data transmission (network-compatible).
Product Detail
Simple and robust sterilising. - Easy, fully automated programmes. - Warming temperature for AGAR production 45 to 60 °C. - Standard steam pot programme. - Microbiologic and procedural security due to dual sensorics, pressure and temperature control. - Compact design. - Standard exhaust steam condenser. - Practical accessories. - Easy cleaning and disposal of residual water. - Prepared for validation port. - Standard castors. - Large, bright display with progress indicators. - Gathering temperature for the sterilisation of liquids adjustable at 95, 90 and 85 °C. - The quick lock can be opened and closed with one finger. - The quick lock and other hot places have a plastic covering. - Thanks to the powder coating the device is always clean and free from fingerprints. - Safety: electro-mechanical safety lock, safety valve, low-water interrupt, overpressure protection switch, overheating protection switch, circuit breaker, fault indicator (visual and audible). - Heating: electrical, with maximum efficiency, directly in the feed water, 3-level protection against overheating. Simple and robust sterilising. - Easy, fully automated programmes. - Warming temperature for AGAR production 45 to 60 °C. - Standard steam pot programme. - Microbiologic and procedural security due to dual sensorics, pressure and temperature control. - Compact design. - Standard exhaust steam condenser. - Practical accessories. - Easy cleaning and disposal of residual water. - Prepared for validation port. - Standard castors. - Large, bright display with progress indicators. - Gathering temperature for the sterilisation of liquids adjustable at 95, 90 and 85 °C. - The quick lock can be opened and closed with one finger. - The quick lock and other hot places have a plastic covering. - Thanks to the powder coating the device is always clean and free from fingerprints. - Safety: electro-mechanical safety lock, safety valve, low-water interrupt, overpressure protection switch, overheating protection switch, circuit breaker, fault indicator (visual and audible). - Heating: electrical, with maximum efficiency, directly in the feed water, 3-level protection against overheating.
Product Detail
Lid with fast locking device and pressure are made from st. steel (SUS 304). For easy cleaning the pressure chamber is polished. The housing is powder coated and also easy to clean. Additional heat protection under the lid handle. The main switch is built-in and is protected by unintentional using. 2 recessed handles facilitate easy manipulation. The feed-water-level is controlled and low water level is indicated. For protection of heating elements the autoclave cannot be started without enough water. An optional feed water connection automatically controls the water level. The exhaust steam condenser cools steam and condensate. This prevents fogging of instruments and unpleasant odours. Loading height is only 750 mm without edges and eyelet at which baskets can get caught. The central quick lock can be actuated with one finger touch. An optional thermo lock with sterilisation time control prevents hazards to the laboratory staff by delayed boiling. The lid remains closed until overpressure inside of sterilisation chamber is balanced. The heat resistant plastic cover protects for touching of hot parts. The lid gasket is a part of the lid, swings towards the top and cannot be damaged by baskets or similar things. There is space for 2 baskets inside. - Safety valve. - Pressure control of max. pressure. - Limiter for max. chamber temperature. - Safety sensor for heating elements. - Approval by TÜV Bayern e. V., CE-mark. - There are 12 installed sterilisation programmes available (according equipment). - Liquid programme including warming programme / without warming programme / with fast recooling or water cooling (depends on model). - Solid sterilisation. - AGAR programme. - Dissolution programmes. - Sterilisation temperature and time can be easily changed before sterilisation start. The steam exhaust (cooling time) is adjustable, for sterilisation of sensitive media. - Timer controlled sterilisation start (overnight programme). This offers an additionally sterilisation. With this programme it is possible to have a ready-to-use AGAR in the morning. - Flexible area code of the ventilation time - so also Durham small tubes can be sterilised. - The programme works from start to end of sterilisation full automatically. The temperature is controlled either direct inside liquids (flexible temperature sensor, optional) or inside the chamber. - The process is temperature controlled and for shortening of heating-up-time additionally pressure controlled. - HGS: device with steam generator and water cooling; connections to demineralised water supply and drainage system are necessary. - HGD: additional vacuum, needs to be connected to industrial water. Lid with fast locking device and pressure are made from st. steel (SUS 304). For easy cleaning the pressure chamber is polished. The housing is powder coated and also easy to clean. Additional heat protection under the lid handle. The main switch is built-in and is protected by unintentional using. 2 recessed handles facilitate easy manipulation. The feed-water-level is controlled and low water level is indicated. For protection of heating elements the autoclave cannot be started without enough water. An optional feed water connection automatically controls the water level. The exhaust steam condenser cools steam and condensate. This prevents fogging of instruments and unpleasant odours. Loading height is only 750 mm without edges and eyelet at which baskets can get caught. The central quick lock can be actuated with one finger touch. An optional thermo lock with sterilisation time control prevents hazards to the laboratory staff by delayed boiling. The lid remains closed until overpressure inside of sterilisation chamber is balanced. The heat resistant plastic cover protects for touching of hot parts. The lid gasket is a part of the lid, swings towards the top and cannot be damaged by baskets or similar things. There is space for 2 baskets inside. - Safety valve. - Pressure control of max. pressure. - Limiter for max. chamber temperature. - Safety sensor for heating elements. - Approval by TÜV Bayern e. V., CE-mark. - There are 12 installed sterilisation programmes available (according equipment). - Liquid programme including warming programme / without warming programme / with fast recooling or water cooling (depends on model). - Solid sterilisation. - AGAR programme. - Dissolution programmes. - Sterilisation temperature and time can be easily changed before sterilisation start. The steam exhaust (cooling time) is adjustable, for sterilisation of sensitive media. - Timer controlled sterilisation start (overnight programme). This offers an additionally sterilisation. With this programme it is possible to have a ready-to-use AGAR in the morning. - Flexible area code of the ventilation time - so also Durham small tubes can be sterilised. - The programme works from start to end of sterilisation full automatically. The temperature is controlled either direct inside liquids (flexible temperature sensor, optional) or inside the chamber. - The process is temperature controlled and for shortening of heating-up-time additionally pressure controlled. - HGS: device with steam generator and water cooling; connections to demineralised water supply and drainage system are necessary. - HGD: additional vacuum, needs to be connected to industrial water.
Product Detail
Specially designed for the requirements in laboratories, these autoclaves make sterilisation processes safe, accurate, reproducible and validatable. 3 model ranges with different performance. Systec DX: For all laboratory applications, incl. sophisticated state-of-the-art sterilisation processes. With numerous options for validatable sterilisation. Systec DE: For basic laboratory applications. With limited options for process optimisation. Systec DB: For simple process applications. No options available for process optimisation. Standard features: - Housing, support frame and pressure vessel made of corrosion-resistant st. steel. - Temperature and pressure range 140 °C, 4 bar. - LCD display and fully automatic microprocessor control. - Code-secured access rights for changing parameters and further safety-relevant intervention. - Flexible PT-100 temperature sensor. - Internal heating elements within the autoclave chamber. - Number of sterilisation programmes: 12. - Internal memory for storing up to 500 sterilisation cycles. - Timer for starting programmes. - Autofill: automatic demineralised water feed for steam generation. - Flexible PT-100 temperature sensor. - Temperature holding function for liquids after programme finish. - Special programme for Durham tubes. - Calculation of F0 value. - Special programme for waste sterilisation with pulsed heat-up for more efficient air exhaust. - Water-cooled steam exhaust, thermostatically controlled. - Programmable automatic door-opening on completion of programme. - RS-232 and RS-485 interfaces for external data transmission (network-compatible). Specially designed for the requirements in laboratories, these autoclaves make sterilisation processes safe, accurate, reproducible and validatable. 3 model ranges with different performance. Systec DX: For all laboratory applications, incl. sophisticated state-of-the-art sterilisation processes. With numerous options for validatable sterilisation. Systec DE: For basic laboratory applications. With limited options for process optimisation. Systec DB: For simple process applications. No options available for process optimisation. Standard features: - Housing, support frame and pressure vessel made of corrosion-resistant st. steel. - Temperature and pressure range 140 °C, 4 bar. - LCD display and fully automatic microprocessor control. - Code-secured access rights for changing parameters and further safety-relevant intervention. - Flexible PT-100 temperature sensor. - Internal heating elements within the autoclave chamber. - Number of sterilisation programmes: 12. - Internal memory for storing up to 500 sterilisation cycles. - Timer for starting programmes. - Autofill: automatic demineralised water feed for steam generation. - Flexible PT-100 temperature sensor. - Temperature holding function for liquids after programme finish. - Special programme for Durham tubes. - Calculation of F0 value. - Special programme for waste sterilisation with pulsed heat-up for more efficient air exhaust. - Water-cooled steam exhaust, thermostatically controlled. - Programmable automatic door-opening on completion of programme. - RS-232 and RS-485 interfaces for external data transmission (network-compatible).
Product Detail
Specially designed for the requirements in laboratories, these autoclaves make sterilisation processes safe, accurate, reproducible and validatable. 3 model ranges with different performance. Systec VX: For all laboratory applications, incl. sophisticated state-of-the-art sterilisation processes. With numerous options for validatable sterilisation. Systec VE: For basic laboratory applications. With limited options for process optimisation. Systec VB: For simple process applications. No options available for process optimisation. Standard Features: - Housing, support frame and pressure vessel made of corrosion-resistant st. steel. - Temperature and pressure range 140 °C, 4 bar. - LCD display and fully automatic microprocessor control. - Code-secured access rights for changing parameters and further safety-relevant intervention. - Flexible PT-100 temperature sensor. - Integrated, separate steam generator. - Number of sterilisation programmes: up to 25 (on request). - Internal memory for storing up to 500 sterilisation cycles. - Timer for starting programmes. - Autofill: automatic demineralised water feed for steam generation. - Flexible PT-100 temperature sensor. - Additional temperature sensor in condense exhaust. - Temperature holding function for liquids after programme finish. - Special programme for Durham tubes. - Calculation of F0 value. - Special programme for waste sterilisation with pulsed heat-up for more efficient air exhaust. - Water-cooled steam exhaust, thermostatically controlled. - Programmable automatic door-opening on completion of programme. - RS-232 and RS-485 interfaces for external data transmission (network-compatible). Specially designed for the requirements in laboratories, these autoclaves make sterilisation processes safe, accurate, reproducible and validatable. 3 model ranges with different performance. Systec VX: For all laboratory applications, incl. sophisticated state-of-the-art sterilisation processes. With numerous options for validatable sterilisation. Systec VE: For basic laboratory applications. With limited options for process optimisation. Systec VB: For simple process applications. No options available for process optimisation. Standard Features: - Housing, support frame and pressure vessel made of corrosion-resistant st. steel. - Temperature and pressure range 140 °C, 4 bar. - LCD display and fully automatic microprocessor control. - Code-secured access rights for changing parameters and further safety-relevant intervention. - Flexible PT-100 temperature sensor. - Integrated, separate steam generator. - Number of sterilisation programmes: up to 25 (on request). - Internal memory for storing up to 500 sterilisation cycles. - Timer for starting programmes. - Autofill: automatic demineralised water feed for steam generation. - Flexible PT-100 temperature sensor. - Additional temperature sensor in condense exhaust. - Temperature holding function for liquids after programme finish. - Special programme for Durham tubes. - Calculation of F0 value. - Special programme for waste sterilisation with pulsed heat-up for more efficient air exhaust. - Water-cooled steam exhaust, thermostatically controlled. - Programmable automatic door-opening on completion of programme. - RS-232 and RS-485 interfaces for external data transmission (network-compatible).
Product Detail
Specially designed for the requirements in laboratories, these autoclaves make sterilisation processes safe, accurate, reproducible and validatable. 3 model ranges with different performance. Systec VX: For all laboratory applications, incl. sophisticated state-of-the-art sterilisation processes. With numerous options for validatable sterilisation. Systec VE: For basic laboratory applications. With limited options for process optimisation. Systec VB: For simple process applications. No options available for process optimisation. Standard Features: - Housing, support frame and pressure vessel made of corrosion-resistant st. steel. - Temperature and pressure range 140 °C, 4 bar. - LCD display and fully automatic microprocessor control. - Code-secured access rights for changing parameters and further safety-relevant intervention. - Flexible PT-100 temperature sensor. - Integrated, separate steam generator. - Number of sterilisation programmes: up to 25 (on request). - Internal memory for storing up to 500 sterilisation cycles. - Timer for starting programmes. - Autofill: automatic demineralised water feed for steam generation. - Flexible PT-100 temperature sensor. - Additional temperature sensor in condense exhaust. - Temperature holding function for liquids after programme finish. - Special programme for Durham tubes. - Calculation of F0 value. - Special programme for waste sterilisation with pulsed heat-up for more efficient air exhaust. - Water-cooled steam exhaust, thermostatically controlled. - Programmable automatic door-opening on completion of programme. - RS-232 and RS-485 interfaces for external data transmission (network-compatible). Specially designed for the requirements in laboratories, these autoclaves make sterilisation processes safe, accurate, reproducible and validatable. 3 model ranges with different performance. Systec VX: For all laboratory applications, incl. sophisticated state-of-the-art sterilisation processes. With numerous options for validatable sterilisation. Systec VE: For basic laboratory applications. With limited options for process optimisation. Systec VB: For simple process applications. No options available for process optimisation. Standard Features: - Housing, support frame and pressure vessel made of corrosion-resistant st. steel. - Temperature and pressure range 140 °C, 4 bar. - LCD display and fully automatic microprocessor control. - Code-secured access rights for changing parameters and further safety-relevant intervention. - Flexible PT-100 temperature sensor. - Integrated, separate steam generator. - Number of sterilisation programmes: up to 25 (on request). - Internal memory for storing up to 500 sterilisation cycles. - Timer for starting programmes. - Autofill: automatic demineralised water feed for steam generation. - Flexible PT-100 temperature sensor. - Additional temperature sensor in condense exhaust. - Temperature holding function for liquids after programme finish. - Special programme for Durham tubes. - Calculation of F0 value. - Special programme for waste sterilisation with pulsed heat-up for more efficient air exhaust. - Water-cooled steam exhaust, thermostatically controlled. - Programmable automatic door-opening on completion of programme. - RS-232 and RS-485 interfaces for external data transmission (network-compatible).
Product Detail
Media preparators designed for preparation and sterilisation of agar-containing nutrient media and other sterile liquids (10 to 120 l nominal volume), with microprocessor-controlled fully automatic programme sequence. The Systec Mediaprep series includes stronger heating elements, rapid cooling, magnetic stirring, inner vessel, temperature controlled door lock, dispensing outlet and inlet port for adding additives. - Fully automatic microprocessor control incorporating 100 programmes. - Sterilisation temperature pre-selectable up to 138 °C / 3.8 bar. - Novel automatic door closure with safety-lock system, lip-gasket out of silicone and opening at the push of a button. - Thermal door lock, controlled by pressure and medium temperature acc. to Pressure Vessel Regulations. - Pressure vessel made out of high quality pharmaceutical grade titanium-stabilised st. steel 1.4571 (V4A, AISI 316 Ti), electro polished, resistant against chemicals, easy to clean. - All sterilisation programmes with pre-selectable sterilisation parameters and automatic programme sequence. - Rapid cooling with recirculating sterile water, heat exchanger and recirculation pump. - Electronic pressure transducer for pressure and temperature regulation. - Autofill: automatic demineralised water feed for steam generation. - Steam exhaust condensation: water-cooled with thermostatic control. - Start by clock / timer for programmable start-time. - Prepared for subsequent printer connection. - RS232 interface for data transfer. - Temperature holding programme for keeping agar solutions warm. - Base plate for vessels, baskets etc. when used as autoclave. - Thermal insulation out of Hanno-Tect, no risk of particle dissociation. - Safety pressure release valve. - Safety cut off at low water level. - Safety cut off at excess temperature. - Direct electrical heated through strong heating elements for fast heat-up. - Fast cooling through recirculation of in-line sterilised demineralised water, cooled by a plate heat exchanger with cooling water connection. - Continuous mixing through a stirrer on the bottom of the media-vessel, contact free driven by a strong magnetic motor. - Permanent temperature control with a PT 100 temperature load sensor, directly inside the media. - Inlet-nozzle with safety screw-closure for filling of additives after sterilisation. - Media removal through a flexible silicone tubing (either by selectable internal pressure inside the chamber and an electronically controlled pinch valve or with an optional peristaltic pump). Furthermore all filling lines for petri-dishes available on the market or other dispensing devices can be connected, without any exception. The inner filling tube and the dispensing nozzle are sterilised in-line, during the sterilisation cycle. - Easy cleaning and operational readiness through exchangeable, removable inner vessel. Thereby no risk of cross-contamination between the different batches. Media preparators designed for preparation and sterilisation of agar-containing nutrient media and other sterile liquids (10 to 120 l nominal volume), with microprocessor-controlled fully automatic programme sequence. The Systec Mediaprep series includes stronger heating elements, rapid cooling, magnetic stirring, inner vessel, temperature controlled door lock, dispensing outlet and inlet port for adding additives. - Fully automatic microprocessor control incorporating 100 programmes. - Sterilisation temperature pre-selectable up to 138 °C / 3.8 bar. - Novel automatic door closure with safety-lock system, lip-gasket out of silicone and opening at the push of a button. - Thermal door lock, controlled by pressure and medium temperature acc. to Pressure Vessel Regulations. - Pressure vessel made out of high quality pharmaceutical grade titanium-stabilised st. steel 1.4571 (V4A, AISI 316 Ti), electro polished, resistant against chemicals, easy to clean. - All sterilisation programmes with pre-selectable sterilisation parameters and automatic programme sequence. - Rapid cooling with recirculating sterile water, heat exchanger and recirculation pump. - Electronic pressure transducer for pressure and temperature regulation. - Autofill: automatic demineralised water feed for steam generation. - Steam exhaust condensation: water-cooled with thermostatic control. - Start by clock / timer for programmable start-time. - Prepared for subsequent printer connection. - RS232 interface for data transfer. - Temperature holding programme for keeping agar solutions warm. - Base plate for vessels, baskets etc. when used as autoclave. - Thermal insulation out of Hanno-Tect, no risk of particle dissociation. - Safety pressure release valve. - Safety cut off at low water level. - Safety cut off at excess temperature. - Direct electrical heated through strong heating elements for fast heat-up. - Fast cooling through recirculation of in-line sterilised demineralised water, cooled by a plate heat exchanger with cooling water connection. - Continuous mixing through a stirrer on the bottom of the media-vessel, contact free driven by a strong magnetic motor. - Permanent temperature control with a PT 100 temperature load sensor, directly inside the media. - Inlet-nozzle with safety screw-closure for filling of additives after sterilisation. - Media removal through a flexible silicone tubing (either by selectable internal pressure inside the chamber and an electronically controlled pinch valve or with an optional peristaltic pump). Furthermore all filling lines for petri-dishes available on the market or other dispensing devices can be connected, without any exception. The inner filling tube and the dispensing nozzle are sterilised in-line, during the sterilisation cycle. - Easy cleaning and operational readiness through exchangeable, removable inner vessel. Thereby no risk of cross-contamination between the different batches.
Product Detail© 2023 Copyright. All Rights Reserved. Unit 19, Euroway House, Roydsdale Way, Bradford, BD4 6SE, UK
© 2023 Copyright. All Rights Reserved. Unit 19, Euroway House, Roydsdale Way, Bradford, BD4 6SE, UK
