Adhesive and embedding materials

PE39.1, Steinel

K956.1, Carl Roth

Easily removable, consists of a hook-and-loop component with self-adhesive back. Fastener is closed by gently pressing hooks into the loops, which is ideal for applications where a high amount of opening and closing is expected. Approx. thickness when closed 2.5 mm. Length 230 cm, width 25.4 mm. Adhesive tape Velcro strip

1263.2, Carl Roth

Fabric tape, 25 mm wide. Wear- and tear-resistant. Good adhesion even on rough surfaces. Labellable. Temperature-resistant up to +130 °C. Adhesive tape tesaband ® Premium

2545.1, Carl Roth

For connecting metal, ceramic or plastics to each other or to other parts of the same material. For pouring out columns in these materials. Epoxy systems Araldit ® G 2 cast resin epoxy resin, liquid Epoxy resin, low viscosity. Suitable for pouring in and embedding electronic components. Hardens at room temperature with hardener H 2 (mixed in a ratio of 10:1 by weight).

90640-67-8, Carl Roth

For connecting metal, ceramic or plastics to each other or to other parts of the same material. For pouring out columns in these materials. Epoxy systems Aradur ® H 2 hardener liquid Liquid.

3131.1, Carl Roth

With an epoxy resin base. Suitable for many materials with the exception of PP, PE, PTFE, PVC and acryl. Fast-setting, heat-resistant up to +100 °C, resistant to alcohol, water, petrol, mineral oils and similar substances, mixing 1:1. Process of setting starts after five minutes, will support itself after another 15 minutes and is fully stable after 8-10 hours. Kit contains 15 ml each of component A and B. Two-component adhesive Araldite ® Rapid liquid

90640-67-8, Carl Roth

For connecting metal, ceramic or plastics to each other or to other parts of the same material. For pouring out columns in these materials. Epoxy systems Aradur ® H 2 hardener liquid Liquid.

1T8P.2, Roth Selection

For gluing, sealing, and coating. Highly chemical-resistant, UV/ozone-resistant. Polymerises at room temperature due to the air humidity to form a permanently elastic rubber. One-component silicone rubber Scrintec ® 650 neutral cross-linking Paste-like, transparent. Temperature-resistant from -50 to +180 °C. Spec. weight 1.03 g/cm 3 , Shore hardness 30°. Particularly suitable for substrates sensitive to corrosion. Odourless.

7085-85-0, Carl Roth

Ethyl cyanoacrylate based single-component instant glue for plastics, metals and porcelain. The adhesive bonds are to a large degree temperature- and chemical-resistant. Not suitable for permanent contact with water. Starts to harden in less than 1 minute and cures fully after 8-10 hours. Storage temp. +10 °C. Shelf life approx. six months. Instant glue CA221 liquid

9639.1, Carl Roth

Transparent, light-resistant thermoplastic acrylic resin for preserving samples, and for coating and sealing wood, stone, metals and other materials. The coating is permanently stable and non-yellowing. Compatible with cellulose, silicone, PVC, and many other plastics and metals. Resistant to water and many chemicals. Dissolves in toluene or ethyl acetate. Can be applied with a brush, spray gun or in an immersion bath. Hardens by air drying or heat exposure (approx. 30 min at 150 °C). Acrylic resin Paraloid™ B-72

2530.1, Carl Roth

For connecting metal, ceramic or plastics to each other or to other parts of the same material. For pouring out columns in these materials. Epoxy systems Araldit ® B 1 adhesive liquid Epoxy-based, low viscosity, transparent. For connecting metal parts and filling hollow spaces. Hardens with hardener H 2 (mixed in a ratio of 100:8 by weight).

9639.2, Carl Roth

Transparent, light-resistant thermoplastic acrylic resin for preserving samples, and for coating and sealing wood, stone, metals and other materials. The coating is permanently stable and non-yellowing. Compatible with cellulose, silicone, PVC, and many other plastics and metals. Resistant to water and many chemicals. Dissolves in toluene or ethyl acetate. Can be applied with a brush, spray gun or in an immersion bath. Hardens by air drying or heat exposure (approx. 30 min at 150 °C). Acrylic resin Paraloid™ B-72