Deliver to
United Kingdom
<p>The product is a solvent for 3D printing, specifically Acetone, with a CAS Number of 67-64-1. It falls under the category of ketones. Its molecular weight is 58.08 g/mol, and it has a Boiling Point of 133 °F at 760 mmHg (NTP, 1992), making it highly flammable. Safety measures include using safety goggles and gloves, no open flames or smoking, and no admittance for unauthorized persons. An indicative occupational exposure limit value for the European Union is 8 hours limit value: 1210 mg/m3 (500 ppm). For more information, refer to the provided URL.</p> <ul> <li>CAS Number: 67-64-1</li> <li>Molecular Formula: C3H6O</li> <li>Molecular Weight: 58.08</li> <li>Exact Mass: 58.041864811</li> <li>Boiling Point: 133 °F at 760 mmHg (NTP, 1992)</li> <li>Melting Point: -137 °F (NTP, 1992)</li> <li>Vapour Density: 2 (NTP, 1992) - Heavier than air; will sink (Relative to Air)</li> <li>GHS Signal Word: Danger</li> <li>Hazard Statements:</li> <li>H225: Highly Flammable liquid and vapor [Danger Flammable liquids]</li> </ul>
Product Detail
<p>This 1-liter container holds Tri(Propylene Glycol) Monomethyl Ether (TPM), a solvent used in 3D printing. It belongs to the category of glycol ethers and polyethers, with a Molecular Weight of approximately 206.28 g/mol. This substance has a warning signal word due to its potential to cause serious eye irritation. It is recommended to handle this chemical with care, following safety guidelines to prevent exposure.</p> <ul> <li>CAS Number: 25498-49-1</li> <li>Molecular Formula: C10H22O4</li> <li>Molecular Weight: 206.28</li> <li>Exact Mass: 206.15180918</li> <li>Boiling Point: 468 °F at 760 mmHg (USCG, 1999)</li> <li>Melting Point: -110 °F (USCG, 1999)</li> <li>Density: Relative Vapour Density (air = 1): 7.1</li> <li>GHS Signal Word: Warning</li> <li>Hazard Statements:</li> <li>H319: Causes serious eye irritation [Warning Serious eye damage/eye irritation]</li> </ul>
Product Detail
<p>This Ethanol, available in a 5-liter container, is classified as a solvent for 3D printing. It belongs to the Alcohols substance group with a molecular weight of 46.07 g/mol. It has a Boiling Point of 173.3°F at 760 mmHg (NTP, 1992) and a Melting Point of -173.4°F (NTP, 1992). Due to its high flammability, it is essential to use safety goggles, keep it away from open flames, and prohibit smoking and open ignition sources near it. This product carries hazard statements for causing serious eye irritation and skin irritation.</p> <ul> <li>CAS Number: 64-17-5</li> <li>Molecular Formula: C2H6O</li> <li>Molecular Weight: 46.07</li> <li>Exact Mass: 46.041864811</li> <li>Boiling Point: 173.3 °F at 760 mmHg (NTP, 1992)</li> <li>Melting Point: -173.4 °F (NTP, 1992)</li> <li>Vapour Density: 1.59 (NTP, 1992) - Heavier than air; will sink (Relative to Air)</li> <li>GHS Signal Word: Danger</li> <li>Hazard Statements:</li> <li>H225: Highly Flammable liquid and vapor [Danger Flammable liquids]</li> <li>H319 (100%): Causes serious eye irritation [Warning Serious eye damage/eye irritation]</li> <li>H315 (100%): Causes skin irritation [Warning Skin corrosion/irritation]</li> </ul>
Product Detail
<p>This 1 liter bottle contains Isopropanol, a solvent commonly used in 3D printing. It belongs to the alcohol family with a molecular weight of 60.10 grams per mole. As a highly flammable liquid and vapor, it requires caution when handling, with no open flames, fire, open ignition sources, or smoking allowed near it. It is also important to use safety goggles while working with this substance. The CAS Number for Isopropanol is 67-63-0.</p> <ul> <li>CAS Number: 67-63-0</li> <li>Molecular Formula: C3H8O</li> <li>Molecular Weight: 60.10</li> <li>Exact Mass: 60.057514874</li> <li>Boiling Point: 180.5 °F at 760 mmHg (NTP, 1992)</li> <li>Melting Point: -127.3 °F (NTP, 1992)</li> <li>Vapour Density: 2.07 (NTP, 1992) - Heavier than air; will sink (Relative to Air)</li> <li>GHS Signal Word: Danger</li> <li>Hazard Statements:</li> <li>H225: Highly Flammable liquid and vapor [Danger Flammable liquids]</li> <li>H318: Causes serious eye damage [Danger Serious eye damage/eye irritation]</li> </ul>
Product Detail
<p>This 1 liter container holds Ethanol, a solvent commonly used in 3D printing. It belongs to the category of Alcohols with a Molecular Weight of 46.07 g/mol. As per the provided data, it has a Boiling Point of 173.3°F and a Melting Point of -173.4°F. Due to its flammability, it is essential to handle this substance with caution, avoiding open flames, open ignition sources, and smoking. Safety goggles should be worn when working with Ethanol. The container carries various workplace labels including Prohibition label, No open flame; fire, open ignition sources and smoking prohibited, No admittance for unauthorized persons, Warning label, Caution - inflammable material, Precept label, and Use safety goggles.</p> <ul> <li>CAS Number: 64-17-5</li> <li>Molecular Formula: C2H6O</li> <li>Molecular Weight: 46.07</li> <li>Exact Mass: 46.041864811</li> <li>Boiling Point: 173.3 °F at 760 mmHg (NTP, 1992)</li> <li>Melting Point: -173.4 °F (NTP, 1992)</li> <li>Vapour Density: 1.59 (NTP, 1992) - Heavier than air; will sink (Relative to Air)</li> <li>GHS Signal Word: Danger</li> <li>Hazard Statements:</li> <li>H225: Highly Flammable liquid and vapor [Danger Flammable liquids]</li> <li>H319 (100%): Causes serious eye irritation [Warning Serious eye damage/eye irritation]</li> <li>H315 (100%): Causes skin irritation [Warning Skin corrosion/irritation]</li> </ul>
Product Detail
<p>Produced to ensure dependable processing results, Dibasic Ester (Dbe) is a versatile solvent designed specifically for use in 3D printing applications. With a density of 1,093 g/cm³ and a boiling point of 216 °C, this solvent offers excellent heat resistance and stability during the printing process. Its flash point at 100 °C ensures safe handling while maintaining optimal performance. By choosing Dibasic Ester (Dbe), you can trust in its ability to deliver consistent outcomes, enhancing the quality of your 3D printed products.</p> <ul> <li><strong>Category:</strong> Solvents for 3D printing</li> <li><strong>Flash point (flp):</strong> 100 °C</li> <li><strong>Density (D):</strong> 1,093 g/cm³</li> <li><strong>Boiling point (bp):</strong> 216 °C</li> </ul>
Product Detail
<p>Manufactured to meet research and production requirements, our Dibasic Ester (DBE) is available in a 5L container. This solvent for 3D printing boasts a density of 1,093 g/cm³ and a flash point of 100°C. Its high boiling point of 216°C ensures efficient evaporation during the 3D printing process.</p> <ul> <li><strong>Category:</strong> Solvents for 3D printing</li> <li><strong>Density (D):</strong> 1,093 g/cm³</li> <li><strong>Flash point (flp):</strong> 100 °C</li> <li><strong>Boiling point (bp):</strong> 216 °C</li> </ul>
Product Detail
<p>This product is Dipropylene Glycol Monomethyl Ether (DPM), a solvent used in 3D printing. It belongs to the category of glycol ethers and polyethers with a Molecular Weight of 148.20 g/mol. The CAS Number for this substance is 34590-94-8. According to the European Union's Directive 2000/39/EC, an indicative occupational exposure limit value has been recommended, with an 8-hour limit value of 308 mg/m3 (50 ppm). This product carries a Warning signal word under the Globally Harmonized System of Classification and Labelling of Chemicals (GHS).</p> <ul> <li>CAS Number: 34590-94-8</li> <li>Molecular Formula: C10H22O3</li> <li>Molecular Weight: 190.28</li> <li>Exact Mass: 190.15689456</li> <li>Boiling Point: 230 °C</li> <li>Density: Relative Vapour Density (air = 1): 6.6</li> <li>GHS Signal Word: Warning</li> <li>Hazard Statements:</li> <li>H373: May causes damage to organs through prolonged or repeated exposure [Warning Specific target organ toxicity, repeated exposure]</li> </ul>
Product Detail
<p>This 25-liter container holds Isopropanol (CAS 67-63-0), a solvent commonly used in 3D printing. It belongs to the alcohol family with a Molecular Weight of 60.10 g/mol. Due to its flammability, it is classified as highly hazardous and requires caution when handling. Safety measures include no open flames, no smoking, and use of safety goggles. It has a Boiling Point of 180.5°F and a Melting Point of -127.3°F. It is heavier than air and will sink.</p> <ul> <li>CAS Number: 67-63-0</li> <li>Molecular Formula: C3H8O</li> <li>Molecular Weight: 60.10</li> <li>Exact Mass: 60.057514874</li> <li>Boiling Point: 180.5 °F at 760 mmHg (NTP, 1992)</li> <li>Melting Point: -127.3 °F (NTP, 1992)</li> <li>Vapour Density: 2.07 (NTP, 1992) - Heavier than air; will sink (Relative to Air)</li> <li>GHS Signal Word: Danger</li> <li>Hazard Statements:</li> <li>H225: Highly Flammable liquid and vapor [Danger Flammable liquids]</li> <li>H318: Causes serious eye damage [Danger Serious eye damage/eye irritation]</li> </ul>
Product Detail
<p>This 5-liter container holds Tri(Propylene Glycol) Monomethyl Ether (TPM), a solvent used in 3D printing. It belongs to the category of glycol ethers and polyethers. Its molecular formula is C10H22O4, with a Molecular Weight of 206.28 g/mol. This substance has a relative Vapour Density of 7.1 compared to air. The GHS signal word for this TPM is "Warning," indicating potential hazards. It may cause serious eye irritation.</p> <ul> <li>CAS Number: 25498-49-1</li> <li>Molecular Formula: C10H22O4</li> <li>Molecular Weight: 206.28</li> <li>Exact Mass: 206.15180918</li> <li>Boiling Point: 468 °F at 760 mmHg (USCG, 1999)</li> <li>Melting Point: -110 °F (USCG, 1999)</li> <li>Density: Relative Vapour Density (air = 1): 7.1</li> <li>GHS Signal Word: Warning</li> <li>Hazard Statements:</li> <li>H319: Causes serious eye irritation [Warning Serious eye damage/eye irritation]</li> </ul>
Product Detail
<p>This product is Dipropylene Glycol Monomethyl Ether (DPM), a solvent used in 3D printing. It belongs to the category of glycol ethers and polyethers, with a Molecular Weight of 148.20 g/mol. The recommended occupational exposure limit value for the European Union is 308 mg/m3 (50 ppm), as per Directive 2000/39/EC. This substance requires a national occupational exposure limit value to be set. The product's CAS Number is 34590-94-8.</p> <ul> <li>CAS Number: 34590-94-8</li> <li>Molecular Formula: C10H22O3</li> <li>Molecular Weight: 190.28</li> <li>Exact Mass: 190.15689456</li> <li>Boiling Point: 230 °C</li> <li>Density: Relative Vapour Density (air = 1): 6.6</li> <li>GHS Signal Word: Warning</li> <li>Hazard Statements:</li> <li>H373: May causes damage to organs through prolonged or repeated exposure [Warning Specific target organ toxicity, repeated exposure]</li> </ul>
Product Detail
<p>The product is identified as Ethyl Acetate, a solvent for 3D printing, with a CAS Number of 141-78-6. It belongs to the carboxylic acid esters substance group and has a Molecular Weight of 88.11 g/mol. According to workplace labels, it is classified as a flammable material and requires safety precautions such as no open flames, wearing safety goggles, and using safety gloves. The European Union has recommended an indicative occupational exposure limit value of 734 mg/m3 (200 ppm) for an 8-hour workday, with a short-term limit value of 1468 mg/m3 (400 ppm).</p> <ul> <li>CAS Number: 141-78-6</li> <li>Molecular Formula: C4H8O2</li> <li>Molecular Weight: 88.11</li> <li>Exact Mass: 88.052429494</li> <li>Boiling Point: 171 °F at 760 mmHg (NTP, 1992)</li> <li>Melting Point: -118.5 °F (NTP, 1992)</li> <li>Vapour Density: 3.04 (NTP, 1992) - Heavier than air; will sink (Relative to Air)</li> <li>GHS Signal Word: Danger</li> <li>Hazard Statements:</li> <li>H225: Highly Flammable liquid and vapor [Danger Flammable liquids]</li> </ul>
Product Detail© 2023 Copyright. All Rights Reserved. Unit 19, Euroway House, Roydsdale Way, Bradford, BD4 6SE, UK
© 2023 Copyright. All Rights Reserved. Unit 19, Euroway House, Roydsdale Way, Bradford, BD4 6SE, UK
